0 FILE hammers.ldr 0 Hammers 0 Name: hammers.ldr 0 Author: Francesco Trotta 0 Unofficial Model 0 ROTATION CENTER -30 0 -30 0 "Pivot 1" 0 ROTATION CENTER 30 0 30 0 "Pivot 2" 1 0 0 -8 0 1 0 0 0 1 0 0 0 1 3031.DAT 0 STEP 1 0 20 -32 -20 1 0 0 0 1 0 0 0 1 3003.DAT 1 0 -20 -32 20 1 0 0 0 1 0 0 0 1 3003.DAT 1 0 -10 -32 -10 1 0 0 0 1 0 0 0 1 3005.DAT 1 0 10 -32 10 1 0 0 0 1 0 0 0 1 3005.DAT 0 The lower hammer was rotated -arccos((sqrt(527)+25)/48) about the parallel to the Z axis through the pivot 1. 1 16 -30 0 -30 0.999093 0 -0.042573 0 1 0 0.042573 0 0.999093 hammer.ldr 0 The higher hammer was rotated arccos(-(sqrt(527)+25)/48) about the parallel to the Z axis through the pivot 2. 1 16 30 0 30 -0.999093 0 0.042573 0 1 0 -0.042573 0 -0.999093 hammer.ldr 0 STEP 1 0 0 -40 0 1 0 0 0 1 0 0 0 1 3031.DAT 0 STEP 1 4 0 -48 -20 1 0 0 0 1 0 0 0 1 3068B.DAT 1 4 0 -48 20 1 0 0 0 1 0 0 0 1 3068B.DAT 1 4 -30 -48 0 0 0 1 0 1 0 -1 0 0 3710.DAT 1 4 30 -48 0 0 0 1 0 1 0 -1 0 0 3710.DAT 0 STEP 1 0 -30 -56 -30 1 0 0 0 1 0 0 0 1 4073.DAT 1 0 30 -56 30 1 0 0 0 1 0 0 0 1 4073.DAT 0 The central plate was rotated arccos((sqrt(527)-11)/36) about the Z axis. 1 4 0 -56 0 0.332124 0 0.943236 0 1 0 -0.943236 0 0.332124 3710.DAT 0 STEP 0 The following block was rotated -arccos((sqrt(527)+25)/48) about the parallel to the Z axis through the pivot 1. 1 4 -59.973 -80 -31.277 0.999093 0 -0.042573 0 1 0 0.042573 0 0.999093 3008.DAT 0 The following block was rotated arccos(-(sqrt(527)+25)/48) about the parallel to the Z axis through the pivot 2. 1 4 59.973 -80 31.277 -0.999093 0 0.042573 0 1 0 -0.042573 0 -0.999093 3008.DAT 0 FILE hammer.ldr 0 Hammer 0 Name: hammer.ldr 0 Author: Francesco Trotta 0 Unofficial Submodel 1 4 -90 -56 0 1 0 0 0 1 0 0 0 1 3009.DAT 1 4 -70 -32 0 1 0 0 0 1 0 0 0 1 3008.DAT 1 4 -120 -80 0 0 0 1 0 1 0 -1 0 0 3038.DAT 1 4 -130 -56 -20 1 0 0 0 1 0 0 0 1 3004.DAT 1 4 -130 -56 20 1 0 0 0 1 0 0 0 1 3004.DAT 1 4 -130 -32 -20 1 0 0 0 1 0 0 0 1 3004.DAT 1 4 -130 -32 20 1 0 0 0 1 0 0 0 1 3004.DAT 1 4 -130 -8 0 0 0 1 0 1 0 -1 0 0 3021.DAT